POOL PUMP AND MOTOR 0.45kw SPECK BADU® PORPOISE
POOL PUMP AND MOTOR 0.45kw SPECK BADU® PORPOISE
The SPECK BADU® Porpoise 0.45kw model is suitable for a SWIMQUIP OR FIBREGLASS 1 bag or a AQUAMAX/AQUAFLO , EARTHCO,SPECK or QUALITY 2 bag sand filter.
The SPECK BADU® Porpoise 0.45kw is suitable for up to a 30,000 litre pool and is best suited with a 1 bag OR 2-bag sand filter. The self-priming pool pump can be installed above or below ground, on a flat surface, away from areas that tend to flood. The pump needs to be installed by a pool professional or electrician.
The BADU Porpoise range of pumps from Speck Pumps combines state of the art material technology with the innovative design and engineering to produce one of the most efficient pumps in the market. The pump can be installed 3m above or below water level. The pump must be installed on a flat surface that would not flood in heavy rain.
Bigger is not always better when it comes to pool pumps. A pool pump that is too large can hinder filtration and can even damage a pool filter and/or heater. It is therefore very important to know the size of a pool before purchasing a pool pump. If there is additional equipment (such as water features) installed into the pool, it will have to be taken it into account when deciding what size pump is going to be purchased. The more equipment is installed into a pool, the more powerful the pump needs to be.
FEATURES:
Pump casing and internal parts made from Polypropylene.
German Engineering and design combined for ultimate efficiency.
Plastic components are 100% recyclable.
Temperature stability up to 60°C.
Total electric separation.
German design mechanical seal using carbon to ceramic sealing surfaces.
Simple servicing.
Fully factory tested.
New 2-part easy screw on / off lid.
Stainless Steel shaft.
Available in 3 sizes to suit all pool applications.
Self-Priming.
24-month ex-factory warranty under normal operating conditions from date of purchase.
Technical data:
Voltage: 1-230V
Power output P2: 0.45kW
Inlet / outlet connection (Rp)2* 50/40
Inlet / outlet pipe, PVC-pipe, d4)* 50/50
Power input P1 (kW) 1-230V 0.67
Power output P2 (kW) 1-230V 1.45 1)
Rated current (A) 1-230V 3.10
Motor speed approx. (rpm) 2840
Max. Water temperature (°C) 60 Max.
Max. Casing pressure (bar) 2.5
The BADU®Porpoise range of pumps combines state of the art material technology with the innovative design and engineering to produce one of the most efficient pumps in the market. The pump can be installed 3m above or below water level. The pump must be installed on a flat surface that would not flood in heavy rain.
| CODE | DESCRIPTION | VOLTAGE | POWER OUTPUT P2 |
| 209.0100.838 | BADU®Porpoise 10 | 1~230V | 0.45kW |
| 209.0160.838 | BADU®Porpoise 16 | 1~230V | 0.75kW |
| 209.0220.838 | BADU®Porpoise 22 | 1~230V | 1~230V 1.10kW |
| TECHNICAL DATA | BADU®Porpoise 10 | BADU®Porpoise 16 | BADU®Porpoise 22 |
| Inlet / outlet connection (Rp)2* | 50/40 | 50/40 | 50/40 |
| Inlet / outlet pipe, PVC-pipe, d4)* | 50/50 | 50/50 | 63/50 |
| Power input P1 (kW) 1~230V | 0.67 | 1.10 | 1.50 |
| Power output P2 (kW) 1~230V | 0.451) | 0.751) | 1.101) |
| Rated current (A) 1~230V | 3.10 | 4.80 | 6.30 |
Original price was: R3,599.99.R3,399.99Current price is: R3,399.99.
POOL PUMP AND MOTOR 0.45kw SPECK BADU® PORPOISE
Product Description:
Experience the efficiency and power of the SPECK BADU® Porpoise 0.45kW pump. Engineered specifically for smaller pools, this model pairs perfectly with SWIMQUIP OR FIBREGLASS 1-bag and AQUAMAX/AQUAFLO, EARTHCO, SPECK, or QUALITY 2-bag sand filters.
Optimized for pools up to 30,000 liters, the BADU Porpoise 0.45kW shines when used alongside a SWIMQUIP OR FIBREGLASS 1 bag or a AQUAMAX/AQUAFLO, EARTHCO, SPECK or QUALITY 2 bag sand filter. Versatility is a cornerstone of its design, allowing installation both above and below ground level. As with all pool pumps, installation on a flat, non-flood prone surface is essential. Engage a pool professional or certified electrician for the installation process.
The BADU Porpoise series from Speck Pumps is the result of meticulous engineering and design, leading to one of the most efficient pool pumps available today. With the capability of installation 3m above or below water level, its flexibility is evident.
Sizing is critical when selecting a pool pump. An oversized pump can not only compromise filtration but also potentially damage pool filters or heaters. Knowledge of the pool size and any additional equipment (like water features) informs the right pump selection. Enhanced pool features typically require more powerful pumps.
Key Features:
- Material Excellence: Pump casing and inner components crafted from Polypropylene.
- German Craftsmanship: German engineering and design ensure top-notch efficiency.
- Environmentally Conscious: 100% recyclable plastic components.
- Temperature Resilience: Stability up to 60°C.
- Safety First: Features total electric separation.
- Mechanical Seal: German design using carbon to ceramic sealing surfaces ensures durability.
- User-friendly: Easy servicing and maintenance.
- Quality Assurance: Each unit is fully factory tested.
- Convenience: New 2-part easy screw-on/off lid system.
- Robust Build: Features a Stainless Steel shaft.
- Versatility: Available in three sizes to fit various pool needs.
- Self-Priming: For easy operation.
- Warranty: Backed by a 36-month ex-factory warranty under standard operating conditions.
Product Specifications:
- Voltage: 1-230V
- Power Output P2: 0.45kW
- Inlet/Outlet Connection: 50/40
- Inlet/Outlet Pipe: 50/50 PVC-pipe
- Power Input P1: 0.67kW (for 0.45kW model)
- Rated Current: 3.10A (for 0.45kW model)
- Motor Speed: Approximately 2840 rpm
- Max. Water Temperature: 60°C
- Max. Casing Pressure: 2.5 bar
What’s Included:
- Speck 0.45kW BADU Porpoise 10 Self-Priming Swimming Pool Pump
- Operation Manual
- Warranty Card
Choose the SPECK BADU® Porpoise 0.45kW for a reliable, efficient, and environmentally-friendly pool pump solution. Always prioritize professional installation and adhere to guidelines for the best results.
Note: Please ensure that the pool’s size and any additional equipment (such as water features) are considered when deciding on the pump size. Make informed choices for a more efficient and enjoyable pool experience.
INSTALLATION INSTRUCTIONS
We recommend that the pump is installed by a qualified pool professional or electrician.
A good installation of your pool pump will result in many years of trouble-free operation. Careful attention must be paid to the following:
1. Piping: The suction and discharge pipes must not be smaller in diameter than the pump connection i.e., Suction pipe diameter 50mm minimum (recommended 63mm), outlet pipe diameter 50mm minimum. Suitable unions should be used on the pump connections or placed in the lines adjacent to the pump connections in case the pump needs to be removed at any time. Do not support the pipework on the pump or vice versa. Make sure all pipe connections are completely water/airtight by using a suitable pipe jointing compound. Keep suction pipe as short as possible and only use pipes that are sufficiently rated to work at a minimum of 4 bar pressure. The suction line should enter the pump straight and horizontally for a length of at least 4 x the diameter of the pipe. The pump is a self-priming pump, which can be installed above or below water level, if you choose to go below, be sure to connect a control valve on your suction pipe between the pool weir/skimmer and the pump, which will prevent your pump being flooded when you open the lid to clean the pump leaf basket. Do not over tighten fittings into the inlet and outlet of the pump. Position pump on a flat level surface not exposed to flooding, as the pump motor is not waterproof.
2. Pump Positioning: (Important for motor cooling): We recommend that the pump be positioned at a level of no more than ± 300mm above your pool water level. Again, we stress the fact to keep the suction line as short as possible. A minimum clearance of 150mm must be allowed behind the motor fan cowling to the nearest obstruction to ensure proper air ventilation and easy access for servicing. The pump house/box must also have provision for adequate drainage facilities.
3. Ventilation: As the electric motor is fan cooled, sufficient ventilation must be allowed at all times during operation. Failure to do this will cause overheating resulting in premature bearing failure and/or motor burnout. If your pump house/box does not have ventilation holes the lid or door should be left open during operation of the pump.
4. Drainage: Flooding of the electric motor is the most common cause of motor failure. It is essential that adequate drainage be provided in the pump house/box. If the motor fails as a result of flooding, then there is no warranty whatsoever irrespective of how the water penetrated the motor. The pump must be protected from rain and flooding.
5. Electric Connections: These must be carried out by suitably qualified people only. Do not change the motor position as it is provided with a drain hole at the bottom to drain off any water which may leak past the mechanical shaft seal. A cable gland must be fitted to the terminal box. NOTE: The length of cable supplied with the pump is for testing only and should be replaced with suitably rated cable. Minimum specification 60245IEC66 (HO7RN-F).
6. Rotation: Before checking the rotation, drain the pump leaf trap of water. The correct rotation is clockwise when viewed from the motor end. Pumps with 220-volt single phase motors are wired at the manufacturer for the correct rotation.
How to keep your pool pump in good running condition
1. Clean the leaf trap in the pump and pool weir regularly.
2. Do not allow dust to accumulate on the motor as this affects the cooling process.
3 Do not leave foreign objects lying on the motor.
4 Change the rubber 0-Ring in the lid at 1-year intervals to maintain a good seal. The face on the leaf trap where the 0-Ring sits must be kept clean and smooth.
6. DO NOT RUN THE PUMP DRY or under closed valve conditions for extended periods.
7. Backwash your filter once a week, or when the pressure exceeds 50% above the starting operating pressure.
8. No Vaseline or petroleum-based lubricants should be used for lubricating 0-Rings or seals. Only silicone paste should be used.
Troubleshooting a pool pump:
Safety first! Isolate the motor before checking for problems.
Motor fails to start:
A) Check that incoming mains wires are connected to the correct motor terminals.
B) Check that the mains supply coming into the motor at the terminals corresponds with the data on the motor name plate.
C) Remove the fan cowl of the motor or insert a screwdriver in the slot of the motor shaft at the fan end and check if the shaft can be rotated freely. If this is not the case, the motor will have to be removed to check if foreign objects are jammed in the impeller.
D) Reset thermal overload (if fitted) at the reset button on motor terminal box.
Motor hums but will not start:
A) Remove the fan cowl of the motor or insert a screwdriver in the slot of the motor shaft at the fan end and check if the shaft can be rotated freely. If this is not the case, the motor will have to be removed to check for faulty bearings, or if foreign objects have become jammed in the impeller. If the shaft can be rotated, check that the capacitor is functioning.
B) Check that phases of motor windings are not down to earth. If they are the motor has been wet or is burned out.
Pump runs but will not pump or pumps poorly.
A) Check direction of rotation.
B) Make sure pump is properly primed.
C) Make sure correct valves are open.
D) Make sure that leaf trap and filter are clean. Backwash filter if necessary.
E) Make sure that leaf trap lid and “0” Ring are sealing properly, and that lid lock handle is tightened firmly. This can normally be diagnosed by air bubbles entering the pool at return point.
Water leaks from drain seal plate flange: The mechanical seal needs to be replaced.
Motor runs noisily:
A) Clean leaf trap and check for any obstruction on the suction line.
B) If this does not help, the motor bearings may need replacement.
Warranty
Thank you for selecting the SPECK BADU® PORPOISE Pool Pump and Motor for your pool needs. We are dedicated to providing you with a high-quality and reliable pool pump. To ensure optimal performance and longevity, please carefully follow the instructions provided in the manual. It’s important to note that warranty claims will only be considered valid if the manual’s instructions are adhered to.
Warranty Coverage: The SPECK BADU® PORPOISE Pool Pump and Motor are covered by a 36-month warranty against defects in material and workmanship. This warranty period starts from the date of purchase.
Fully Factory Tested: Rest assured that your SPECK BADU® PORPOISE Pool Pump and Motor have undergone rigorous testing at the factory to ensure their quality and functionality.
Sole Responsibility of the Manufacturer: In the event of a valid warranty claim, the manufacturer’s sole obligation to the end user is as follows:
Repair: If the SPECK BADU® PORPOISE Pool Pump and Motor, or any of its components, are found to be defective in material or workmanship, the manufacturer will perform necessary repairs without any cost to you. Our goal is to promptly restore your pump’s functionality.
Limitations and Exclusions: Please note that this warranty constitutes the complete warranty for the product and supersedes all other warranties, whether expressed or implied. This includes any implied warranties by distributors, salespersons, or fitness for a specific purpose. The warranty specifically covers defects in materials and workmanship of the product itself. It does not extend to travel, installation, or labor costs related to the removal or reinstallation of the product.
The warranty will be rendered null and void if damages or issues result from failure to comply with the manual’s instructions or accepted engineering practices.
Retaining proof of purchase is important, as warranty claims may require it.
For any warranty-related inquiries or claims, please contact our Customer Support. We are here to assist you throughout the process and provide the necessary guidance.
Only logged in customers who have purchased this product may leave a review.
Related products
Reviews
There are no reviews yet.